If your Kenmore Refrigerator Model 795 is not cooling, the most common causes are a locked compressor, defective electronic control board, or a damaged evaporator. To troubleshoot this issue, you can check the condenser coils, defrost timer, heater, cold control, sensor, thermostat, compressor, fans, door switch, and air damper.
You can also try resetting the control board and temperature settings. Seeking the help of a professional technician may be necessary if the problem persists.
Common Reasons For Not Cooling
Is your Kenmore refrigerator model 795 not cooling as it should? This can be a frustrating problem to face, but there are common reasons why this might be happening. Identifying the cause of the cooling issue can help you troubleshoot and resolve the problem efficiently. Here are three common culprits for a Kenmore refrigerator not cooling: Locked Compressor, Defective Electronic Control Board, and Damaged Evaporator.
Locked Compressor
A locked compressor can be a major reason why your Kenmore refrigerator is not cooling. The compressor is the heart of the cooling system, responsible for circulating refrigerant and maintaining the desired temperature. If the compressor is locked or not functioning properly, it will not be able to cool the refrigerator effectively.
There are a few signs that can indicate a locked compressor. You might notice that the refrigerator is making unusual noises, such as a buzzing sound, or that it is not cooling at all. If you suspect a locked compressor, it is best to seek professional help to diagnose and repair the issue.
Defective Electronic Control Board
The electronic control board plays a vital role in regulating the temperature and overall functioning of your Kenmore refrigerator. If the control board becomes defective, it can disrupt the cooling process and lead to a refrigerator that is not cooling as it should.
One indication of a defective control board is if the display panel is not functioning correctly or showing error codes. Additionally, if the control board is not sending the proper signals to the compressor or other components, it can result in inadequate cooling. In such cases, it may be necessary to replace the electronic control board to restore optimal cooling performance.
Damaged Evaporator
The evaporator coil is responsible for absorbing heat from the refrigerator and helping to cool the interior. If the evaporator coil becomes damaged or develops a leak, it can impair the cooling process and prevent the refrigerator from maintaining the desired temperature.
You might notice signs of a damaged evaporator, such as a buildup of frost or ice on the evaporator coil, or a warm refrigerator despite the compressor running. If you suspect an issue with the evaporator coil, it is recommended to consult a professional technician to assess and repair the problem.
In conclusion, a Kenmore refrigerator model 795 not cooling can be attributed to various factors, such as a locked compressor, defective electronic control board, or damaged evaporator. Identifying the specific problem can help you troubleshoot and resolve the cooling issue effectively. If you are unsure about diagnosing or repairing the problem, it is always best to seek professional assistance to ensure optimal performance of your Kenmore refrigerator.
Quick Fixes
Discover quick fixes for troubleshooting the Kenmore Refrigerator Model 795. From checking condenser coils to testing sensors and thermostats, these easy steps will help you identify and resolve common issues. Stay cool with these simple solutions!
Check Condenser Coils
One of the common issues that can cause your Kenmore Refrigerator Model 795 to not cool properly is dirty or clogged condenser coils. Over time, these coils can accumulate dust, dirt, and debris, which hinders their ability to release heat efficiently. To fix this, you can simply clean the condenser coils using a vacuum cleaner or a soft brush. Make sure to unplug the refrigerator before doing any maintenance.
Defrost Timer
The defrost timer plays a crucial role in regulating the automatic defrost cycle in your Kenmore refrigerator. If the defrost timer malfunctions, it can cause a build-up of ice on the evaporator coils, resulting in inadequate cooling. To troubleshoot the defrost timer, locate it at the back of the refrigerator and manually advance the timer using a screwdriver. If the refrigerator starts to cool properly after this, it’s likely that the defrost timer needs to be replaced.
Check Heater
The heater in your Kenmore refrigerator is responsible for melting the frost on the evaporator coils during the defrost cycle. If the heater is faulty or not working correctly, it can lead to ice build-up and insufficient cooling. To check the heater, use a multimeter to test for continuity. If there is no continuity, the heater needs to be replaced.
Cold Control
The cold control, also known as the thermostat, regulates the temperature inside your Kenmore refrigerator. If the cold control is not functioning correctly, it can cause your refrigerator to be too warm or too cold. To test the cold control, set it to the desired temperature and listen for a click. If you don’t hear a click or notice any changes in temperature, you may need to replace the cold control.
Knocking The Knob
Sometimes, a simple fix for your Kenmore refrigerator not cooling properly is just knocking the temperature control knob. Over time, the knob can get stuck or become loose, affecting the temperature settings. Give the knob a gentle tap or twist it to ensure a proper connection. If this doesn’t resolve the issue, further troubleshooting may be required.
By following these quick fixes, you can troubleshoot and resolve common issues with your Kenmore Refrigerator Model 795. Remember to always prioritize safety and consult a professional if you are unsure or uncomfortable performing any repairs yourself.
Testing And Troubleshooting
Testing and Troubleshooting
When it comes to troubleshooting your Kenmore Refrigerator Model 795, it’s important to know how to properly test and identify potential issues. In this section, we will guide you through the testing process for the cold control, sensor, thermostat, defrost heater, and damper motor. By following these steps, you can diagnose and resolve common problems with your refrigerator.
How To Test The Cold Control
The cold control, also known as the temperature control, regulates the temperature inside the refrigerator. To test the cold control:
- Disconnect the power to the refrigerator.
- Access the control panel or locate the temperature control knob.
- Using a multimeter, set it to ohms or continuity testing.
- Remove the control panel or knob cover.
- With the multimeter leads, touch the terminals of the cold control.
- If the multimeter shows continuity or changes resistance while adjusting the temperature, the cold control is functioning properly. If not, it may need replacement.
How To Test The Sensor
The sensor inside your Kenmore Refrigerator Model 795 monitors the temperature and sends signals to the control board. To test the sensor:
- Identify the location of the sensor, usually located near the evaporator coils or inside the refrigerator compartment.
- Disconnect the power to the refrigerator.
- Use a multimeter to test the resistance of the sensor.
- Compare the resistance reading with the temperature chart provided by the manufacturer.
- If the resistance is within the specified range, the sensor is working correctly. If not, it may need replacement.
Thermostat Fail
The thermostat failure can result in erratic temperature control or a complete failure of the cooling system in your Kenmore Refrigerator Model 795. If you suspect a thermostat failure:
- Check for power supply and continuity in the thermostat using a multimeter.
- If there is no continuity in the thermostat, it is likely defective and needs to be replaced.
- Ensure any temperature settings are correctly adjusted.
- Verify that the thermostat is receiving power from the control board or power supply.
Defrost Heater
The defrost heater is responsible for melting ice and frost build-up on the evaporator coils. If you observe excessive ice or frost, it may indicate a problem with the defrost heater. To test the defrost heater:
- Disconnect the power to the refrigerator.
- Locate the defrost heater, usually behind the back panel of the freezer compartment.
- Using a multimeter set to ohms, test the continuity of the defrost heater.
- If there is no continuity, the defrost heater is likely defective and needs to be replaced.
Test Damper Motor For Continuity
The damper motor controls the flow of cold air from the freezer to the refrigerator compartment. If you are experiencing temperature imbalances, it could indicate a faulty damper motor. To test the damper motor for continuity:
- Disconnect the power to the refrigerator.
- Locate the damper motor, usually located in the refrigerator compartment.
- Using a multimeter set to ohms, test the continuity of the damper motor.
- If there is no continuity, the damper motor is likely defective and needs to be replaced.
Resetting The Control Board
If you’re experiencing issues with your Kenmore Refrigerator Model 795, resetting the control board can often resolve the problem. The control board is the brain of the refrigerator, responsible for regulating functions such as temperature and cooling cycles. Resetting the control board can help troubleshoot issues and get your refrigerator back up and running smoothly. Here are two methods to reset the control board:
Unplug And Reset The Refrigerator
To start, you can try unplugging your refrigerator from the power source. This action essentially resets the control board and allows any potential glitches to be cleared. Here’s how you can do it:
- Locate the power cord of your Kenmore refrigerator.
- Unplug the cord from the electrical outlet.
- Leave the refrigerator unplugged for at least 5 minutes. This duration allows the control board to fully reset.
- After 5 minutes, plug the power cord back into the electrical outlet.
- Wait for the refrigerator to power on and observe if the issue persists.
Turn Off And Stabilize Temperature Settings
If unplugging and resetting the refrigerator doesn’t resolve the issue, you can try turning off and stabilizing the temperature settings. Here’s how you can do it:
- Locate the control panel on your Kenmore refrigerator. It is usually located inside the refrigerator compartment.
- Press the “Power” or “Off” button to turn off the refrigerator.
- Once the refrigerator is turned off, locate the temperature control buttons.
- Set the freezer and fridge temperature settings to the recommended levels. These settings can be found in the user manual or on the control panel.
- Wait for the refrigerator temperature to stabilize. This may take a few hours.
- After the temperature has stabilized, turn the refrigerator back on and check if the issue has been resolved.
Resetting the control board of your Kenmore Refrigerator Model 795 can often help troubleshoot and resolve various issues. If the problem persists after attempting these troubleshooting steps, it may be best to consult a professional technician or contact Kenmore customer support for further assistance.
Additional Resources
When it comes to troubleshooting your Kenmore Refrigerator Model 795, having access to additional resources can be incredibly helpful. Whether you’re looking for manuals, discussions on appliance repair forums, or Kenmore replacement parts, these resources can provide valuable information and solutions to common refrigerator issues.
Kenmore Refrigerator Manuals
When you’re faced with a refrigerator problem, referring to the Kenmore Refrigerator Manuals can be a great starting point. These manuals provide detailed instructions on how to troubleshoot and resolve various issues that may arise with your specific refrigerator model. From understanding error codes to adjusting temperature settings, the manuals offer step-by-step guidance to help you get your refrigerator back in working order.
Appliance Repair Forums
Another valuable resource for troubleshooting your Kenmore Refrigerator Model 795 is appliance repair forums. These online communities are filled with experts and individuals who have experienced and resolved similar refrigerator issues. By participating in discussions or searching through previous threads, you can gain insights and advice from those who have encountered and overcome similar problems. You may even find detailed instructions or video tutorials on how to fix specific issues.
Kenmore Replacement Parts
If you determine that you need to replace a specific part in your Kenmore Refrigerator Model 795, it’s essential to have access to genuine Kenmore replacement parts. Using authentic parts ensures compatibility and reliability, helping you restore your refrigerator’s functionality. Kenmore offers a wide range of replacement parts, including water filters, compressors, evaporators, and more. You can easily find these parts through official Kenmore retailers or authorized distributors, ensuring you get the right parts for your refrigerator.
Frequently Asked Questions
How Do I Run Diagnostics On My Kenmore Elite 795 Refrigerator?
To run diagnostics on your Kenmore Elite 795 refrigerator, follow these steps:
1. Check condenser coils and defrost timer. 2. Verify the heater and cold control. 3. Test the sensor, thermostat, and defrost heater. 4. Inspect the compressor, fan, and door switch. 5. Ensure proper electrical connections and motor functioning. For detailed instructions, refer to online videos or the Kenmore refrigerator manual.
What Causes A Kenmore Elite Refrigerator To Stop Cooling?
A Kenmore Elite refrigerator may stop cooling due to a locked compressor, defective electronic control board, or a damaged evaporator.
How Do I Reset My Kenmore Refrigerator Control Board?
To reset your Kenmore refrigerator control board: 1. Unplug your refrigerator. 2. Turn off the refrigerator and freezer from the control panel. 3. Reset your freezer and fridge temperature settings. 4. Wait for the refrigerator temperature to stabilize. Make sure to follow these steps to properly reset the control board of your Kenmore refrigerator.
How Do You Reset The Compressor On A Kenmore Refrigerator?
To reset the compressor on a Kenmore refrigerator, follow these steps: Unplug the refrigerator, turn off the control panel, reset the temperature settings, and wait for the temperature to stabilize.
What Are The Common Reasons For A Kenmore Elite Refrigerator Not Cooling?
The most common reasons your Kenmore Elite refrigerator is not cooling are a locked compressor, defective electronic control board, or a damaged evaporator.
Conclusion
To troubleshoot issues with your Kenmore Refrigerator Model 795, it is important to check various components such as condenser coils, defrost timer, heater, cold control, and thermostat. Additionally, ensure that the fans, door switch, compressor, and air damper are working properly.
Common causes for refrigerators not cooling include a locked compressor, defective electronic control board, or a damaged evaporator. If you are experiencing cooling problems, try resetting the control board, adjusting temperature settings, and allowing the refrigerator temperature to stabilize. For further assistance, refer to the provided resources or consult with a professional technician.
